Electric immersion heaters are a popular choice where a gas supply is not present. Gas water heating usually has lower run cost.
How they Work
- There is a jacketed heating element in the water cylinder.
- Usually the element has a built in adjustable thermostat, but there are also some with no stat built in, and a separate external stat attached to the tank, usually at about 1/3 the way up the tank.
- There is an on/off switch (or occasionally a timer) on the supply to the heater.
- Newer elements also have a secondary thermal cutout built in
2 Element Systems
Economy 7 Systems
Dual tariff systems typically heat the lower element at night, and use the smaller top element for top-up heat in the day.
27" elements heat the whole cylinder. This is the most common size.
11" elements are used for top heat only, and for whole cylinder heating with Fortic cylinders.
14", 18" 30" and 36" elements are also available, but are less common than 11" & 27". The element should generally be 3" - 6" shorter than the max length physically fittable.
The majority of faults can be found by testing just 3 resistances:
- across the 2 heating element terminals
- should be somewhere vaguely in the region of 20 ohms, but can vary a fair bit.
- across the 2 thermostat terminals
- should be far below 1 ohm when cold.
- From heating element terminals to casing.
- should be open circuit.
This common fault causes current to flow from live to earth in the element. This causes problems:
- RCD trips if on an RCD protected power feed
- Current flow is often increased, which can sometimes cause fuse blowing, MCB tripping or hot or burnt wiring accessories
The only solution is to replace the element.
Elements often split open during the last phase of their life. Rapid corrosion of the resistance wire then occurs, breaking the element circuit. However the element continues to operate for a fair time by conducting through the water.
Despite what we were taught about electricity and water as children, this condition does not cause any deaths or injuries in the UK, and is a widespread occurrence. In fact the principle of feeding mains electricity direct through the water is standard practice in industry, albeit with a bit more precaution than is applied to domestic hot water. It is known as electrode heating.
In this phase of life,
- resistance testing from element terminals to casing shows low resistance
- Heating may be faster or slower than usual due to less well controlled current
- Element may cycle on & off due to excess heating
- A heater on an RCDed feed trips the RCD immediately.
The only solution is to replace the element.
Burning of the thermostat connections is another common failure, and results in failure to function. Parts of the stat may be burnt to charcoal.
To test for this, resistance test across the thermostat connections. R should be a small fraction of an ohm with a cold element. If higher, the stat contacts are damaged.
If this occurs, the possible solutions are:
- Replace element & thermostat in one
- Replace thermostat only, if possible
- File the contacts clean and check the temp setting afterwards
- It used to be compliant to wire across the built-in stat and add an external 13A rated stat strapped to the tank, but this no longer meets the requirement for a secondary non-resettable thermal cutout, and most strap-on stats aren't 13A rated.
Either way one should clean out all traces of carbon deposits. The tiniest amounts left behind can cause an electrical short.
Burning or Fishy Smell
May be due to burning or cooking of the thermostat, the FCU or an end of the flexible cable. Inspection should show any discoloured and burnt material.
This problem is sometimes caused by a split element consuming above rated current, so it's a good idea to check the element resistances as well.
Not enough hot water
This is caused by any of:
- thermostat set too low. This can be a problem with new replacement elements, which often have stats that wont go as high as older ones, but sometimes the cylinder can require a higher temp to have enough HW capacity.
- replacement element too short
- For curved element systems, replacement element is mounted the wrong way up, with the curved end pointing up instead of down
- For 2 element systems, bottom element not working
- With heat banks, a badly scaled exchanger reduces rate of heat throughput, but not capacity. The tell tale sign is that fast flowing HW is not hot enough, but slow the flow down and the temperature is restored.
- Insufficient HW system capacity for new appliances, eg power shower
- Turn up stat. If it won't go high enough, it may be possible to wire it out of circuit and replace with an external stat, but a secondary non-resetting temperature cutout is also now mandated.
- Replace the replacement element with the correct longer size
- Refit element with curved end down
- Troubleshoot lower element & its associated parts
- Replace or descale exchanger. Consider scale prevention before the exchanger.
- Applying as many options in Increase Hot Water Capacity as possible may be enough. Turn down shower pumping rate. If these measures aren't enough, a larger HW cylinder is needed.
See also Increase Hot Water Capacity for more options.
Water too hot
Thermostat failed, mounted too low, hanging off or fallen off the cylinder.
It is not recommended to put an immersion heater on a ring circuit. The continuous 13A load leaves the circuit with reduced spare ampacity.
It is not recommended to put an immersion heater on a 13A plug. As well as loading the ring it can cause plug overheating.
- Daytime electricity is around 12p/unit
- Economy 7 about 6.5p/unit
- Gas (mains) about 4p/unit, factoring in boiler inefficiency
As well as the usual domestic elements, its possible to get low & high power elements, 1kW to 18kW, and 3 phase elements. eg
For industrial heating, electrode heating is also used. Power passes through a ballast to limit current, then directly through the water to heat it. It's perfectly safe done correctly.
When removing an old element, the cylinder should be kept full of water while loosening the element to discourage the tank from crumpling. Loosen the heater with an immersion heater spanner. It's more effective to tap it with a hammer than rotate it by hand. If very stiff, turning it slightly both ways sometimes helps. Once it's moving a bit freer the cylinder can be drained to below the level of the heater.