Difference between revisions of "Spanner"

From DIYWiki
Jump to navigation Jump to search
(pics replace)
Line 148: Line 148:
  
 
===Immersion heater spanner===
 
===Immersion heater spanner===
 
+
[[image:Immersion spanner 0766-6.jpg|thumb|Immersion]]
[[image:Immersion spanner 0766-5.jpg|thumb|Immersion]]
 
 
 
 
 
  
 
* A large spanner for immersion heaters.
 
* A large spanner for immersion heaters.
 
 
* undoing an immersion heater in an empty cylinder can buckle the cylinder.
 
* undoing an immersion heater in an empty cylinder can buckle the cylinder.
 
 
* Old immersion heaters should be loosened a bit while the cylinder is still full
 
* Old immersion heaters should be loosened a bit while the cylinder is still full
 
 
* Once the immersion is moving a bit, then drain the tank to below the heater and remove.
 
* Once the immersion is moving a bit, then drain the tank to below the heater and remove.
 
 
  
 
==Wrenches==
 
==Wrenches==

Revision as of 15:03, 23 January 2010

Spanner types

Open end

Open ended


Ring

Not as prone to slipping off as open end, but usable in less situations.


Combination

Combination

A combination spanner has 2 different types of driver on the one spanner. Most often these are open and ring, but other combinations are also available.


Ratchet

A real boon where getting the spanner onto the nut is difficult, eg for some car work.


Adjustables

Adjusable spanners are called wrenches.


Self adjusting

Self adjusting
  • One can handle a range of sizes
  • Handy for odd sizes
  • Not as robust as fixed sizes, and more prone to slipping off in use.
  • Useful for portable tool kits


Box spanner

Box spanner

The forerunner of the socket set. Lighter, cheaper, weaker, and no longer very popular.


Their greater depth is sometimes useful for recessed fixings. So also is their relative thinness, when the recessed fixing is in a narrow hole.


Their much lighter weight than sockets makes them useful in portable tool kits.


Socket set

Socket set

Cast steel sockets can apply much more torque and control than open ended spanners, but are more cumbersome and can't always be used.


Extension bars enable clearing nearby obstacles.


Torque wrenches enable setting bolts or nuts to precise torque. A few different types exist.


Deep sockets can be used where bolt threads protrude, and on spark plugs.


Size

Sockets have a square hole in to drive them, and this can be any of several sizes:

  • 1/4" - for very light duty work eg appliance case screws
  • 3/8" - light & medium duty. Can do a fair percentage of car work
  • 1/2" - good for a lot of general purpose use, most popular for car work, but not big sizes or high torque jobs
  • 3/4" - good for heavy duty work, eg washing machine bearings, tougher items on cars and larger vehicles.
  • 1" - industrial duty, professional car mechanics
  • 1.5" and 2.5" also exist, but aren't often seen.


1/2" drive is by far the most popular size.


Stamped spanner

Stamped

Most spanners are cast, these ones are stamped from sheet metal. The result is a thin flat spanner with lower weight and strength. They're plenty strong enough for a wide range of tasks, but the thin metal edge makes applying high forces with a bare hand painful. Fine for medium force.


Stamped spanners tend to be made from mild steel rather than the tougher rust proof chrome vanadium steel used for most spanners, so should always be stored dry as they rust readily.


Stamped spanner set

Stamped spanners tend to come as accessories supplied with an appliance. Manufacture cost is much lower than cast spanners. Whole sets of stamped spanners are rarely seen.



Multispanner

Small multispanner

A stamped sheet spanner with many different size cutouts around the edges, or a casting with many recesses. Available in a few well known patterns (flat sheet, dog bone, and the ring type shown). These don't give good performance and can't be recomended for general DIY use, they're better suited to bikes where the low weight and size is more important than decent usability, and they're only occasionally used. The small ring shaped ones (pictured) are the least friendly to use.


Basin wrench

Basin wrench

Can undo taps from a greater variety of positions than other spanner types. Useful when working in confined positions.


Self adjusting basin wrenches are also quite popular.


Immersion heater spanner

Immersion
  • A large spanner for immersion heaters.
  • undoing an immersion heater in an empty cylinder can buckle the cylinder.
  • Old immersion heaters should be loosened a bit while the cylinder is still full
  • Once the immersion is moving a bit, then drain the tank to below the heater and remove.

Wrenches

Spanners are known as wrenches in American English. Adjustable spanners are usually called wrenches here.



Spanner sizes

What the size means

Metric sizes and most imperial sizes (AF but not BSW or BSF) are 'across flats' dimensions, ie from top to bottom on this diagram:

  ____ 
 /    \
/      \
\      /
 \____/


Whitworth sizes and BSF, which aren't too common nowadays, are measured quite differently.


Substituting sizes

One handy tool is a list of the exact metric sizes of all common imperial spanners. This is because some imperials make a good fit for metric nuts and vice versa - although many don't. A good example is 3/4", which is 19.05mm.


This is definitely not a recommendation to use the sizes that don't fit well, this can damage nuts & spanners, and injure hands when they slip.


More information and tables here: Size conversion


More torque please

Extension tubes

Fitting steel tube over a spanner to get much more leverage works, but is a known cause of injuries. Where large leverage is needed, a socket is a safer option, with long handles available.


Impact wrench

When even more torque is needed, an impact wrench is the best choice. This is much better controlled way to apply high torque than hand tools.




See Also