Search results
Jump to navigation
Jump to search
- ...bulbs]] run at high pressure and are known to very occasionally explode. A shower of high speed & very high temperature broken bulb pieces is probably not be6 KB (887 words) - 21:54, 29 September 2018
- *[[Installing an electric shower]] *[[Installing a concealed shower mixer valve (retrofit)]]11 KB (1,453 words) - 22:41, 29 May 2024
- ...t to prevent these chemicals depositing themselves inside pipes, tanks and shower heads. Nor should it be confused with a water FILTER, which removes bacteri6 KB (1,104 words) - 10:59, 7 January 2022
- *Dedicated high current circuit [[MCB]] & [[Cables|cable]] supplying shower ...D]] on the other. Generally the [[RCD]] side is used to supply sockets and shower, with most other items on the non-RCD side.26 KB (4,100 words) - 00:12, 16 September 2021
- ...r more. The smaller sizes being adequate for properties that have a single shower/bathroom. Larger sizes become more appropriate for larger properties with m ...a cold water outlet point after the pressure reducing valve to supply e.g. shower mixing valves which work better when their hot and cold supplies are at the15 KB (2,499 words) - 21:20, 5 May 2021
- ===Shower=== *Use a low flow shower head20 KB (3,343 words) - 11:58, 24 September 2022
- * A 15 minute shower uses more water than a bath7 KB (1,141 words) - 13:44, 7 April 2012
- ...violations. No problems with lights, fans or sockets too close to a bath, shower or sink. He may find a lack of labels or lack of identifying sleeves on swi6 KB (1,076 words) - 18:50, 26 October 2022
- * Is there a shower pump? Location? How to isolate (electrical and water)?8 KB (1,230 words) - 17:29, 21 August 2022
- ...getting some old carpet and underlay around the cab and I've screwed some shower-tidys on the cab back wall. It'll do for several years, there's not much to7 KB (1,256 words) - 23:38, 17 February 2023
- ...ically designed for hanging towels over for warning and drying in bath and shower rooms. Chrome plated or white painted ladder types are widely available at14 KB (2,237 words) - 00:48, 9 December 2010
- ...e are particularly vulnerable to electrical shock injury, such as bath and shower rooms. Bonding also helps mitigate the risks of conductive parts of a house9 KB (1,461 words) - 04:49, 1 December 2012
- ...how mains powered extractor fans of the type often found in bathrooms and shower rooms can be wired.11 KB (1,928 words) - 13:06, 5 January 2024
- * Hot & Cold water pipes to sink, bath, shower11 KB (1,751 words) - 02:17, 6 September 2017
- ...e boiler located in a cabinet right next to the sink (and not far from the shower). One had a "proper" door, and one didn't. Are cabinets located within ba9 KB (1,507 words) - 11:14, 29 March 2012
- ...able of carrying this current. A good example of this would be an electric shower or an immersion heater supply cable where there is no end user action, or t Say we have an electric shower with a design current <math>I_b</math> of 41A, and a cable run of 19m, inst23 KB (3,726 words) - 23:12, 31 January 2024
- ...pipework was brought up to enter the loft through the floor where the new shower is shown on the plan above. In the shower room, I ran in wiring for a humidistat controlled fan, a shaver light, and69 KB (12,721 words) - 22:49, 31 January 2024
- Water resistant adhesive is needed for shower and over bath use. More basic types fall off after a bit.10 KB (1,764 words) - 21:08, 24 January 2013
- ...he wall. I also routed a pipe channel to it. This is in a side-room toilet/shower where the inner lining is plastic 10mm cladding and not metal stud. The dec10 KB (1,800 words) - 18:39, 6 November 2021
- ...wall - say when cutting in electrical accessory boxes, or making access to shower valves. They are also very effective for removing old grout from between ti13 KB (2,110 words) - 23:58, 10 September 2018