Electrical Installation

From DIYWiki
Revision as of 02:09, 25 September 2008 by John Rumm (talk | contribs) (→‎Lifting floors: Added some floor types and options)
Jump to navigation Jump to search

This article is all about the non engineering side of electrical installations. Its purpose is to explain some of the techniques that are used to when installing electrical equipment and wiring in typical domestic situations.

This page is Under Construction
Whilst all Wiki pages are subject to continuing improvement the author(s) of this page have included this disclaimer to alert the reader that the page may be particularly
  • incomplete - important sections may be entirely missing
  • inaccurate - significant facts and figures may be quite wrong
  • misleading - the text may not convey the author(s) intended meanings

In particular treat any safety-related sections of the text (e.g. relating to electrical work) with great caution.

If you are thinking of editing this page please be aware that the original author(s) of this page may be actively working on it at this moment, so changes you make may clash with theirs. (The Wiki software will warn you of conflicts if this happens.) Checking the page's history tab for frequent recent edits can warn you if changes by others are likely.


Wall chasing

See the wall chaser article for more detail on the options for cutting cable chases in plaster and masonry.

Getting past coving and skirtings

It is all well and good chasing a wall with your trusty SDS drill or wall chaser, but what happens when you reach some architectural feature that you don't want to go hacking through, like a deep skirting board or ornate plaster cornice or moulding?

  • Long drill bit: A very long drill bit (we are talking a minimum of 400mm here to get behind small items like picture or dado rails, or more realistically a stonking great 1m long bit bit for skirtings and coving!) can be a handy way to continue a chase behind the feature you are trying to avoid. Ideally one would need to drill straight up or down through the plaster to achieve this. This is usually impossible since you can't get the drill in the right place, or at the right angle since the wall is in the way. With small obstructions (dado etc) this may not matter, drilling down behind it at a slight angle will still be ok. For a longer vertical chase, the longer bit will be required. The trick here is to apply some sideways force to the bit as you drill. It should be possible to bend the drill such that its tip *is* parallel to the wall, while keeping the drill body and you hands at the slight angle required due to the obstruction of the wall.
  • Cranked gouging chisel: specially made SDS gouges can also work well for getting behind smaller items.
  • Using the other side of the wall: As simple as it sounds, in some cases the solution to avoiding difficult chases, might be to simply use the other side of the wall. This can be ideal for a cable chase on a tiled wall in a bathroom. It can also often save time where adjacent rooms have light switches "back to back" on the dividing wall - only one chase is required for the pair. Note One will need to take care that cable routes are within the prescribed zones expected - even if this means installing an extra accessory to mark the position.

Under floors

Lifting floors

Techniques for lifting floors
Type of floor Methods
Traditional floorboards A traditional boarded floor is one of the easier ones to get under! The traditional approach simply uses a pry bar and or bolster chisels to leaver it up. Sometimes you also need to cut a board. There are a number of approaches to this:
  • floorboard saw (one with a curved toothed section) will allow a plunge cut to be made over a joist.
  • Japanese style azebeki saws are even better.
  • Bend 'n' saw - sometimes if the boards have enough bend in them, you can leaver one up in the middle of a section, and slide a chisel under it propped up on the adjacent boards. This will then let you at it with a traditional panel or tenon saw.
  • If you know the thickness of the boards, then you can snap off a jigsaw blade such that when the jigsaw is at the lowest part of its stroke, the blade is the same depth (or fractionally deeper) than the boards. If needs be a hold can be drilled to allow the blade some entry room.
  • If you are in a hurry, a plunge cut with a circular saw - again with the depth set to no deeper than the board depth.
  • Oscillating multi-tools like the Fien Multimaster and the similar concept Bosch PMF 180, really come into their own here since they allow perfect neat plunge cuts into boards. The very narrow kerf of the blade also leaves far less visible damage once the floor is put back down again.
Tongue and grove floor boards Similar to the above, except you will also have to rip cut through (or split off) the tongue on the board first, in order to be able to lift it.
Chipboard sheet Generally far harder to work with since the boards are not only tongue and grooved at the edges, they are also large (typically 8' x 2'). In many modern houses, its also not uncommon for the partition walls to be built over the floor panels or at least the skirtings etc to be fixed over them. This can make removal of a whole board impossible. The best way to deal this this floor is to cut an access panel:
  • The Trend Routabout jig is designed for this purpose, and makes it easy to not only get access, but also fix the hole afterwards.
  • The jigsaw, oscillating tool, and circular saw options described above also work. You will need to use screws and battens under the cut edges however to restore the strength of the floor afterwards (chipboard is string in gig sheets, but small strips are quite weak without support on all sides).
Laminate While not easy it is possible to remove a plank of laminate in a floor. For the click together type, it may be simplest to start un-clicking panels at the edge of the room, and work your way back to where you need your access point. For glued panels, you will need to cut out a board. The way to do this is with a circular saw (preferably a small one - cordless ones are ideal). Set the cut depth to laminate thickness, and cut through the board all round close to its perimeter. Once the main bit is removed, use a chisel to break away the remaining edges from the adjacent boards.

To replace the board you will need to cut away the underside section of the groove edges of the new plank, and then glue and lower the new board into place. Depending on how cleanly you were able to remove the tongue from the goove of the adjacent board, you may also need to cut this off the new board.

Entry via a ceiling

The lateral thinkers way to get under a "difficult" upstairs floor. In many cases some new plasterboard and a bit of patching is a much quicker solution that lifting an engineered wood floor and underlay, or clearing a particularly cluttered room.

Over Ceilings

In Walls

Pull wires / cords / tapes

Push rods and sticks

Essential general tools

Much of the mechanical aspects of wiring have little to do with the things that one traditionally associates with the work of an electrician, and are really nothing more than general building and carpentry tasks.

Type Description
SDS Drill (3 function) The ability to not only drill holes, but also quickly and neatly chisel out holes for socket boxes, and neat wall chases make the SDS drill a wonderful time saver.
Cordless drill / driver In general cordless tools are very handy to have for electrical work since you will often be working in areas without power. Making holes, and fixing things in place probably come right near the top of list of tasks faced by anyone undertaking electrical work. A medium size (say 14.4V or better) combi drill is ideal for this sort of work. Having the hammer facility can make drilling holes into masonry for wall plugs far simpler.

Essential electrical tools

Type Description
Insulated screwdrivers (VDE) VDE tools are insulated and tested to to a high standard. This ensures that should the metal part of the tool make contact with live metalwork, no harm will come to the person holding the other end. These are absolutely essential when working on electrical installations. Not just for the rare occasions where live working is required, but the far more typical cases where one is working in close proximity to live circuits, or even on circuits that really ought to be dead, but are not!

All things said and done, you can make do some ordinary screwdrivers for jobs not involving work on electrical fittings etc, and you may choose to buy a limited set of VDE insulated drivers: a medium phillips (typical for MCB terminals) and a small and medium flat blade for other terminals.

Side Cutters VDE insulated side cutters are essential (one day, you *will* pick the wrong cable to cut). Side cutters are used for cutting cables and wire to length, and they are also often invaluable for stripping cables of their outer insulation. Some cutters also include specific facilities for wire stripping, [eg].
Wire Strippers Good wire strippers make life very much simpler (while it is true that someone proficient with side cutters can often strip a wire quite satisfactorily with them as well, there is far more scope for bruised knuckles, damaged conductors, and tatty looking wire ends without them). The style of wire cutter is much a matter of personal preference. Side strippers are quick and easy to use - especially one smaller wires. The end action ones may be better for tough insulation found on the thicker and also special purpose wires. Some people also like to have an automatic wire stripper. These can make repeated stripping operations very much quicker.
Combination pliers regular square nosed medium set are useful for holding, bending, and twisting wires, tightening locknuts etc. In fact anywhere you need extra gripping power.
Long nose pliers A good pair of long nose pliers are the ideal tool for fishing wires out of awkward corners, and holding tricky wires in place as you tighten terminal screws. Note however that even with VDE insulated ones, care must be taken, since they have a large expanse of exposed metalwork that could easily short against live parts or earthed casework.

Ratchet action cable crimper

Essential for making sound wire joints which will later become inaccessible, or where space is too restrictive to allow terminal (aka "choccie blocks") to be used. See the Cable crimping article for full details of how to use these.

Essential test gear

Type Description
Volt stick
Socket Tester

Further test gear

For anything other than basic alterations and additions to existing circuits, some more sophisticated test equipment is really required. This items can be bought as separate units or as an integrated tester that combines all the functions.

Type Description
Insulation resistance tester ("megger")
Earth loop impedance tester
RCD Tester

Good workmanship

Mechanical protection

  • Capping
  • Conduit
  • Grommets
  • Strain relief sleeves
  • Glands
  • Minimum bend radii


  • Clips
  • Trunking

Making good

Once you have installed and tested all your new wiring, there is the rather more mundane task of filling all the wholes, and reinstating the fabric of the building before you lose too many household pets or children into floor voids or incur the wrath of the style police!

Filling chases

Replacing floor boards

See also