Difference between revisions of "Fill"
Jump to navigation
Jump to search
m (Fill a hole moved to Fill) |
(asstd m) |
||
| Line 1: | Line 1: | ||
| + | '''How to fill holes in a wall or ceiling''' | ||
| + | |||
| + | |||
==Small holes== | ==Small holes== | ||
Small holes are easy & simple to fill. | Small holes are easy & simple to fill. | ||
# remove any loose material from the hole | # remove any loose material from the hole | ||
| − | # if the hole is in [[Sheet Materials|plasterboard]], best to Knives|cut]] off any unbonded little flaps of paper | + | # if the hole is in [[Sheet Materials|plasterboard]], best to [[Knives|cut]] off any unbonded little flaps of paper |
# Squish [[filler]] into the hole with a [[Scraper|filling knife]] | # Squish [[filler]] into the hole with a [[Scraper|filling knife]] | ||
| − | # Either wipe it with the knife | + | # Either wipe it with the [[Knives|knife]] or [[scraper]] to make it dead flat, or let it set proud and sand it level later. |
Tips: | Tips: | ||
* If you're filling paper surfaced [[Sheet Materials|plasterboard]], do the mimimum of [[Sandpaper|sanding]], if any. | * If you're filling paper surfaced [[Sheet Materials|plasterboard]], do the mimimum of [[Sandpaper|sanding]], if any. | ||
| − | * If the hole is open backed or deep, push something to the back of the hole first to block it, such as screwed up paper. | + | * If the [[Drill bit|hole]] is open backed or deep, push something to the back of the hole first to block it, such as screwed up paper. |
* If the sides of your hole are crumbly, even after removing loose stuff, brush them with diluted [[Adhesive|PVA]] before filling. (Many other [[glue]] types could also be used) | * If the sides of your hole are crumbly, even after removing loose stuff, brush them with diluted [[Adhesive|PVA]] before filling. (Many other [[glue]] types could also be used) | ||
| + | * [[Filler]]s often shrink slightly on setting, making deep layers crack. To deal with this, fill the hole to slightly below the final surface first, then fill full once its set. | ||
==Medium holes== | ==Medium holes== | ||
| − | Some holes are too big to support [[filler]] without it slumping or dropping out. These need | + | Some holes are too big to support [[filler]] without it slumping or dropping out. These need something to support the [[filler]], then are filled as for small holes. Any of the following can be used: |
* any type of rigid board, eg [[Sheet Materials|plasterboard]], [[Sheet Materials|hardboard]], etc | * any type of rigid board, eg [[Sheet Materials|plasterboard]], [[Sheet Materials|hardboard]], etc | ||
* cardboard just about works | * cardboard just about works | ||
| Line 22: | Line 26: | ||
==Large holes== | ==Large holes== | ||
| − | Large closed backed holes can be filled with [[Filler|plaster, artex, sand & cement, sand & lime, filler]] or anything similar. Limit the depth of each layer, letting each set before applying the next. Max depth per layer depends on the filler used. | + | Large closed-backed holes can be filled with [[Filler|plaster, artex, sand & cement, sand & lime, filler]] or anything similar. Limit the depth of each layer, letting each set before applying the next. Max depth per layer depends on the filler used. |
Large open backed holes require fitting with [[Sheet Materials|plasterboard]] before filling. Often a piece a little bigger than the hole is cut, inserted at 90 degrees and turned round to block the hole. Its then held in place before filling somehow, eg | Large open backed holes require fitting with [[Sheet Materials|plasterboard]] before filling. Often a piece a little bigger than the hole is cut, inserted at 90 degrees and turned round to block the hole. Its then held in place before filling somehow, eg | ||
| Line 33: | Line 37: | ||
Another way to use PB in the hole is to cut it to fit entirely within the hole, fit it in just very slightly recessed, using wedges of cardboard/wood/paper to hold it temporarily, and fill around the edges to stick it in place, pressing the [[filler]] in deep. Remove wedges when set and complete the filling. | Another way to use PB in the hole is to cut it to fit entirely within the hole, fit it in just very slightly recessed, using wedges of cardboard/wood/paper to hold it temporarily, and fill around the edges to stick it in place, pressing the [[filler]] in deep. Remove wedges when set and complete the filling. | ||
| − | Another option is to fit some wooden sticks behind the hole that will support the new plasterboard piece. The sticks are either [[glue]]d to the existing [[Sheet Materials|plasterboard]], screwed to the existing plasterboard, or for a much stronger result fixed to the existing woodwork behind the plaster. The new plasterboard can then be [[screw]]ed to the wood. | + | Another option is to fit some wooden sticks behind the hole that will support the new plasterboard piece. The sticks are either [[glue]]d to the existing [[Sheet Materials|plasterboard]], screwed to the existing plasterboard, or for a much stronger result fixed to the [[Stud wall|existing woodwork]] behind the plaster. The new plasterboard can then be [[screw]]ed to the wood. |
==Fillers== | ==Fillers== | ||
| − | [[Filler]] | + | See [[Filler]] for filler types |
Not enough filler? | Not enough filler? | ||
Revision as of 12:40, 20 February 2011
How to fill holes in a wall or ceiling
Small holes
Small holes are easy & simple to fill.
- remove any loose material from the hole
- if the hole is in plasterboard, best to cut off any unbonded little flaps of paper
- Squish filler into the hole with a filling knife
- Either wipe it with the knife or scraper to make it dead flat, or let it set proud and sand it level later.
Tips:
- If you're filling paper surfaced plasterboard, do the mimimum of sanding, if any.
- If the hole is open backed or deep, push something to the back of the hole first to block it, such as screwed up paper.
- If the sides of your hole are crumbly, even after removing loose stuff, brush them with diluted PVA before filling. (Many other glue types could also be used)
- Fillers often shrink slightly on setting, making deep layers crack. To deal with this, fill the hole to slightly below the final surface first, then fill full once its set.
Medium holes
Some holes are too big to support filler without it slumping or dropping out. These need something to support the filler, then are filled as for small holes. Any of the following can be used:
- any type of rigid board, eg plasterboard, hardboard, etc
- cardboard just about works
- metal mesh inside the hole
Use of lightweight filler increases the size of hole that can be filled unsupported.
Large holes
Large closed-backed holes can be filled with plaster, artex, sand & cement, sand & lime, filler or anything similar. Limit the depth of each layer, letting each set before applying the next. Max depth per layer depends on the filler used.
Large open backed holes require fitting with plasterboard before filling. Often a piece a little bigger than the hole is cut, inserted at 90 degrees and turned round to block the hole. Its then held in place before filling somehow, eg
- string and weight for ceilings
- tape, doesn't always work though
- bit of filler round the edges
- iron wire
- etc
Another way to use PB in the hole is to cut it to fit entirely within the hole, fit it in just very slightly recessed, using wedges of cardboard/wood/paper to hold it temporarily, and fill around the edges to stick it in place, pressing the filler in deep. Remove wedges when set and complete the filling.
Another option is to fit some wooden sticks behind the hole that will support the new plasterboard piece. The sticks are either glued to the existing plasterboard, screwed to the existing plasterboard, or for a much stronger result fixed to the existing woodwork behind the plaster. The new plasterboard can then be screwed to the wood.
Fillers
See Filler for filler types
Not enough filler?
- Fill much of the depth of the hole with polystyrene etc first
- Poke gravel into the filler to use less