From DIYWiki
Revision as of 09:38, 10 January 2013 by NT (talk | contribs) (Laying flat section)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Flex is stranded electrical wire used for all plug-in mains appliance leads. It is also called flexible cable.

Cable on the other hand is unstranded mains wire not suited to repeated flexing, and is used for fixed installations.


Cable colours 1179-5.jpg

Current colours:

  • L - brown
  • N - blue
  • E - green/yellow striped

Old colours: (until about 1970)

  • L - red
  • N - black
  • E - green

Colours on US appliance leads:

  • black = live
  • white = neutral

2 Core Flexes

Flex 2 core flat 0835-8.jpg

Flexes are available with 2 or 3 cores (conductors). 2 core flex is only suitable for appliances that don't need an earth connection (marked DoubleInsulated.jpg), and should not be used for extension leads with 3 pin sockets.

2 core flexes are available in both round and oval shape. Oval (flat) uses less material, but any twisting of the flex is visible, whereas it isn't with round.


Flex 4 core 0380-5.jpg

Multicore mains flexes are also available for those uncommon tasks requiring more conductors. Non-mains multicores, such as alarm cable, are not suitable for mains use.



Flex blue n pink 0379-4.jpg

Most flex has PVC insulation rated to 70°C.

90°C PVC is also available for use in hot locations, such as for immersion heaters. A higher temp rating also means a given conductor size may carry more current in some (very limited) circumstances. however practically it is not usually possible to take advantage of this increase in capacity since the normal BS 1363 plugs, sockets and flex connection units are not rated for the higher temperature.


Flex Arctic 0378-6a.jpg

Arctic flex remains flexible at low temperatures, whereas regular PVC stiffens. Arctic flex is used for outoor appliances, eg on building sites. It is rated for use down to -40°C.

On sites yellow is used for 110v and blue for 240v.


TRS (tough rubber sheath) is a flex with greater mechanical strength and damage resistance than PVC. It is used when some degree of rough use can be expected.

VIR is discussed further down.


Flex cloth 0381-5.jpg

Flexes with a cloth outer have rubber inner insulation. These have a high temperature rated outer surface. They are well known for their use on irons.

Old cloth insulated flexes are prone to kinking, with the inner rubber insulated wires poking out at the kinks. New cloth insulated flexes have a layer of rubber under the cloth that discourages this from happening.

The rubber inner insulation can harden and break at the ends. This is often seen on old cloth flexes. When this occurs the flex can be cut back several inches to reveal healthy flex, and reconnected, if the rest of the flex is still healthy.


Soft high temp plastic insulation sometimes found on irons. Much more heat resistant than PVC

Hi vis

Flex hivis 0378-6b.jpg

Used with mowers etc, where visibility is important for safety

Figure of 8

Figure 8 flex 5709-3.jpg
Twin flex clear-2.jpg

Figure of 8 shaped plastic flex was formerly used for low current mains uses. It has a single layer of insulation only, and live conductors are easily exposed by minor damage. It was used in several colours, including black, brown, white and clear.

Such flex has been unlawful to fit to mains appliances for decades, but is still occasionally seen in use. Today this flex type is used as speaker wire.

Twisted Pair

Twisted pair 0842-7.jpg

2 core cloth & rubber (VIR) twisted mains flex with no outer sheath was once in common use. Most was dark red or brown. This flex has been obsolete for decades, and is rarely seen today. Occasionally its seen on historic electrical goods, and when found is usually in a dangerous condition. Apart from not meeting modern safety requirements, the rubber tends to harden, perish and disintegrate over time, exposing bare live wires. Despite once being in widespread use, it is rarely seen today because it deteriorates badly over time.

Conductor Sizes

Flex conductor size (mm²) Approx max current (PVC insulation)
0.5 3A
0.75 6A
1.0 10A
1.5 15A
2.5 20A
4.0 32A

Note that current carrying capacities are only approximate, and vary with exact construction and materials used for the flex.

For data on how much 90°C insulation changes current ratings, see Cable

Laying flat

PVC flexes have a habit of not laying flat, and bending wherever they were folded in the past. 3 types of flex can avoid this problem:

  • silicone
  • rubber
  • string filled pvc

See Also