Silicone
Silicone sealant is a versatile and flexible waterproof sealant with a multitude of applications (see the Putty & Mastic article for other types of sealer).
It is particularly good in situations where you need to make a waterproof gap seal, but cannot completely eliminate movement between the parts to be sealed. Its key benefits are:
- Remains permanently elastic after curing.
- Long life expectancy in many applications.
- Does not shrink.
- Keeps its colour and is waterproof.
- Resists most chemicals and solvents.
- Is non toxic after curing.
- Has very good adhesion to glass and all commonly used building materials.
- Resists temperatures ranging from -60°C to +200°C
Known issues:
- Supports heavy mould growth
- the "sanitary" version with fungicide delays mouldering, but doesn't prevent severe mould
- Takes a little skill and practice to apply neatly
- its stretchability is limited, it pulls away where this is exceeded
- best not cleaned with a scourer, or it can break up in time
Uses
- Sealing gaps round baths, showers, windows, worktops
- Fixing mirrors or glass to tiled surfaces
- Sealing gutters and downpipes
- Repairing rubber trim on cars
- Moulding into soft rubber goods of most shapes
- Making reusable flexible moulds
- Gluing aquaria together
- Noise reducing rubber feet
Types of silicone
There are a a number of different types of sealant available, some with specific uses and capabilities. Note that not all of these attributes are exclusive, some products will combine attributes from several of these categories. All the silicone sealants we are discussing here are Room Temperature Vulcanised (RTV) products. These cure at normal room temperature when exposed to moisture present in the air.
General purpose and builders silicone
This is the basic general purpose silicone sealant. It sticks well to most building materials and offers good elasticity and durability.
Sanitary silicone
A silicone that includes a fungicide to reduce formation of mould on silicone that is frequently exposed to moisture. To reduce the chance of mould forming it is important to get the surface of the silicone joint as smooth as possible. This also makes cleaning it easier. Improving ventilation in rooms that suffer persistent high moisture levels can also help reduce mould growth.
Glazing Silicone
Typically a sealant that cures to a very clear finish and offers very good adhesion to glass. Used for bedding in glazing panels, and sealing around the edge of the glass in windows and doors.
Frame Sealant Silicone
This is a tough sealant designed to accommodate large amounts of movement, and it is also better able to withstand exposure to the weather and UV radiation than other types of sealant. It adheres well to most building materials. It is designed for sealing round window and door frames. Often available in a variety of colours designed to match wood and other common framing materials.
Neutral Cure Silicone
Most silicone sealants release acetic acid while curing. This gives off a characteristic vinegar like smell. In some circumstances this odour may be undesirable, or the acetic acid may have a negative impact on the materials being sealed (for example some clear polycarbonate materials may suffer slight staining when exposed to acetic acid). Neutral cure silicone products reduce or eliminate the production of acetic acid while curing. Often the better quality sealants also tend to be neutral cure products.
Food Safe Silicone
A silicone product with very low toxicity designed for use in food contact applications. Often used for sealants inside refrigerators.
High Temperature Silicone
Designed to withstand high temperatures when cured (typically up to 260 degrees celsius, but 300C rated is available). Often finds applications in electrical and industrial equipment, and for making seals between high temperature surfaces.
Aquarium Silicone
A very tough silicone designed for glueing and sealing glass in aquarium applications. Do not use building silicones for fish tank construction.
Other specialist silicones
There are a number of other specialist silicone products designed for different industrial uses. For example in the electronics industry. Many of these are designed for coating circuit boards to resist moisture penetration, or for "potting" assemblies, joints, and circuits.
High & Low Modulus
Sometimes silicone sealants are described as 'High modulus', or 'Low Modulus'. The low modulus products are more elastic and well suited to sealing tasks that need to accommodate more movement without failing. The high modulus products are less able to accommodate movement but will make a stiffer and more rigid final seal. The high modulus products tend to withstand repeated cleaning attempts better than the softer more flexible low modulus ones.
How much movement is allowed?
One of the primary causes for sealant failure is expecting the sealant to accommodate more movement than it is designed to be able to withstand. While silicone sealants are very strong and elastic when under shear loads, they have only limited adhesive properties under tension. This can result in the bead of sealant pulling away from one side of the joint.
As a guideline you should not expect a bead of sealant to expand by more than 10% of its original size (some products claim to be able to withstand up to 20% movement, but this does expect almost perfect application conditions). So for example a 10mm wide bead of silicone ought to be able to withstand stretching to 11mm repeatedly without failure. However it is unrealistic to expect a 5mm wide bead of silicone to expand to 10mm.
If you are unable to reduce the amount of movement expected in a joint, then you need to ensure that the silicone bead width forming the seal is larger so as to accommodate the movement and stay within the 10% threshold.
Another technique to improve the success rate of seals that need to withstand high movement, is to apply the sealant when the joint is at the far limit of its expected movement, and then only allow the joint to return to its "normal" position once the sealant is cured. A typical example would be when sealing round a bath. It is better to fill the bath with water before sealing. Allow the sealant to cure before draining the water. The will place the sealant under compression when the bath is empty, rather than under tension when it is full.
Clear Silicone
Ensure very good lighting when using clear silicone, otherwise its hard to see clearly and get the detailing good.
Accelerated Curing
If a very fast set is needed, mix damp chalk dust into the silicone, and it sets in a couple of minutes.
Life Expectancy
Good quality sealants should produce joints that last in excess of 10 years. Some products are even guaranteed a 25 year life.
Shelf life of the unused product is limited. Keep an eye on best before dates. Unusable silicone is either hard in the tube, or else fails to cure after application.
Application
One of the keys to successful application is to make sure the joint to be sealed is clean and free from contaminants and grease first.
Observe 'use by' dates, or silicone may be solid in the tube, or fail to cure once applied. If newly applied silicone has no vinegar smell, set may fail to occur (unless its a neutral cure product).
To get a good consistent bead of silicone in a single application is a skill that is difficult to master. More realistically you will need to tool the bead to its finished form after application to get good results.
The simplest 'tool' is a finger! For best results dipping it in some form of release agent first will help stop the silicone sticking to the finger in preference to the joint. Suitable release agents include some spray on window cleaner products or 50% washing up liquid. The difficult thing to achieve with a finger however is a good bead shape. You tend to end up with a concave bead with fine feathered edges. This is not a very strong bead shape, and the fine edges will tend to peel away when wiping the seal. Using masking tape applied down the outside edges of the joint can improve the edge by creating a slightly thicker edge with a cleaner transition.
Some consider that using a finger rather than a tool increases the likelihood of mildew formation later on, even when so-called mould-resistant silicone is used.
Tools made from wood soaked in 50-50 washing up liquid & water can also be used to tool wet silicone.
Most people find that good results are easy to achieve using one of the commercial application tools. The two most common ones are the "Fugi", and the "Fugenboy" by Elch. The video for the Fugi tool on the Plumbworld site here, shows just how well they work.
These tools receive good reviews on news:uk.d-i-y.
Home made applicators can also be made from polypropylene. They need to be feathered to give a suitable profile. Old ice cream tubs can work well as a good source of material.
Removal and Cleanup
While still wet, silicone can be cleaned up using a solvent such as isopropyl alcohol (IPA). The aerosol cans available from suppliers like CPC are ideal for this.
Once silicone has set it is very much harder to remove. One of its great attractions is that relatively few solvents or chemicals will attack it. It is possible to purchase proprietary silicone "eater" products. These slowly dissolve small quantities of cured silicone into a sticky goo that can then be wiped off, but the bulk of the silicone needs to be removed first.
The best approach for removing any quantity of it is a combination of mechanical and chemical. According to a poster who does this task regularly for clients, you need:
Shopping list;
- Snap off knife - a basic Stanley knife is not as good.
- Get the Hamilton Scraper & some spare blades (don't buy the SF or TS versions)
- Stainless steel scourers like these (Supermarkets sell them)
- Microfibre cloths (Supermarkets again (Tesco ones rated particularly well)).
- White spirit.
- Small sharp chisel
- Application tool type tool set
- Elbow grease.
- Beer.
Procedure
- Start with the snap off knife - extend about 2" of the blade, hold it flush with the tiles & slice along the silicone vertically.
- Scraper next, but don't scrape. Hold flat horizontally against tray & slide along sideways - use it as a knife.
- Use scraper against tiles & tray as a scraper to remove any residue.
- Vigorously rub with dry microfibre cloth - this will pull out any tiny bits.
- Use small chisel to get into corners or behind taps etc (e.g. on a bath).
- Wet scourer with white spirit & gently scrub off any stubborn residue (they don't scratch).
- Use white spirit on microfibre cloth to degrease area.
- Buy a brand name anti fungal silicone & tool in with the application tool.
- Drink beer.
Mould & cleaning
Mould is a real issue with silicone used in wet environments such as bathrooms. Silicones contain acetates which feed mould.
Mould resistant silicones are available, but they go mouldy in wet environments too.
Regular wiping or spraying of thin bleach helps to delay and slow the growth of mould, but does not get rid of it.
The best solution to mould is to use another type of sealant. See Putty & Mastic for the options.
It is possible to clean black mould off silicone sealant. Apply folded toilet paper and bleach, and leave in place overnight. Badly blackened silicone takes around 4 applications to look more or less like new.
Alternative sealants
There are a variety of other sealants available, and these each have their uses. For more details on alternative sealants see the Putty & Mastic article.