Search results
Jump to navigation
Jump to search
Page title matches
File:Spruce resin 563-3.jpg Spruce timber, showing a knot and resin pockets.(2,145 × 645 (77 KB)) - 21:54, 15 June 2010
Page text matches
- ===Resin=== High resin content can make a mess on [[Saws|saw blades]]. Resin can be cleaned off with a solvent.3 KB (428 words) - 19:42, 12 October 2014
File:Leakfix 0067-4.jpg Leakfix polyester resin(967 × 513 (58 KB)) - 22:57, 28 August 2010
File:Epoxy 0070-4.jpg Epoxy resin cartridge(1,272 × 524 (129 KB)) - 00:03, 17 August 2010
File:Epoxy wall threaded rod 1324-2.jpg Threaded rod fixed into wall with epoxy resin(818 × 818 (43 KB)) - 01:03, 1 May 2009File:Spruce resin 563-3.jpg Spruce timber, showing a knot and resin pockets.(2,145 × 645 (77 KB)) - 21:54, 15 June 2010- [[Adhesive#Epoxy Resin|Epoxy]] very tough, bonds securely, fills gaps well. Mainly for structural ...esin|resin]]s including resorcinol, urea-formaldehyde, phenol formaldehyde resin, etc.4 KB (546 words) - 00:23, 22 February 2013
- ===Resin Fillers=== Car body filler is a tough [[Adhesive|Polyester resin]]preparation with numerous [[Special:Allpages|DIY]] uses, both as filler an8 KB (1,332 words) - 19:33, 16 December 2010
- ...ions are removed and replaced with the magnesium and calcium ions from the resin bed. The waste water from this operation is flushed down the drain, as is t ...iants. To my knowledge there is no softener which actually senses when the resin is exhausted they all either meter the water (having previously been set to6 KB (1,104 words) - 10:59, 7 January 2022
- ===Resin Terrazzo=== ...version of terrazzo. It is typically a quarter of an inch thick, based in resin, and looks like concrete terrazzo.6 KB (918 words) - 22:35, 18 July 2018
- [[Adhesive|Car body filler (polyester resin)]] is a tough durable quick setting filler used where good strength and pro Car body filler is a 2 pack [[Adhesive|polyester resin]] with many DIY uses.3 KB (500 words) - 15:51, 28 June 2017
- * Not as strong an attachment as a resin fixed bolt1 KB (217 words) - 16:37, 8 June 2020
- ==Epoxy Resin== [[image:Clear epoxy 0067-6.jpg|thumb|Clear epoxy resin]]15 KB (2,414 words) - 19:46, 30 April 2012
- The support for the remainder would come from uprights resin bonded into holes drilled into the existing masonry. ...dge into the top of the hole to prop the post at the right angle while the resin cured.13 KB (2,400 words) - 23:28, 11 September 2023
- * [[Adhesive|Resin]]3 KB (373 words) - 23:53, 29 September 2012
- * Insert [[Adhesive|resin glue]] into hole, refit plug, let set. * Use resin, with or without plug11 KB (1,781 words) - 12:19, 7 December 2016
- ...n plugs]. These are little [[wallplug]]s designed for pins. Or any type of resin [[glue]] can go into masonry [[Drill bit|holes]] instead, and the cable cli3 KB (419 words) - 17:03, 2 January 2019
- ;[[Adhesive#Polyester resin|Car body filler]] : A tough durable filler with many uses. Polyester resin with inert fillers.6 KB (893 words) - 15:11, 11 August 2012
- ===Resin filled capsule=== ...ection in a plastic housing, and fill it with [[Adhesive|resin]]. Suitable resin filled connector kits are available. Underground electricity distribution u13 KB (2,188 words) - 00:15, 15 December 2013
- Stockhom tar is smoked cooked pine resin. Tar waterproofs as well as preserves, and is thus a good choice for the bo4 KB (695 words) - 20:57, 4 November 2011
- ...e mastic gun and push the rod in, twiddle it round a bit to distribute the resin, and leave it alone. 5 mins later it will be fixed! (work time and full cur14 KB (2,454 words) - 00:47, 28 April 2024
