Difference between revisions of "Terminating SWA"
|Line 26:||Line 26:|
This is a picture of the seven parts of the somewhat inappropriately named three part gland kit. This is the exterior waterproof style of gland. The interior version lacks the extra gland nut with the rubber insert that is used to seal the the gland against the cable.
=Step 1 - Assemble the gland parts on the wire=
=Step 1 - Assemble the gland parts on the wire=
Revision as of 21:58, 7 July 2008
For the smaller and intermediate sizes of SWA, the quickest way to cut it to length is using a large pair of bolt croppers:
(for very large sizes of cable a hydraulic assisted cutter or saw may be a better option).
For the purposes of this example we will terminate some XLPE insulated (PVC sheathed) 4mm² two core SWA:
(4mm² is in the small to medium size range of SWA cables typically used in domestic work (1.5mm² being the smallest and 16mm² probably being the largest). Note however all these can be thought of as "small" when compared to the monster sizes used in industry and public power distribution systems such as 400mm² cables with working currents in excess of 600A!)
There are a couple of different types of gland kit suitable for SWA cable; internal and external. Both types will ensure a very rigid fixing of the cable can be made to the box or unit where it connects. and that a good electrical connection can be made to the cable armour wires (used for protective earthing). In the case of the exterior gland kits, they also ensure the connection is waterproof.
- A proper gland kit is the only acceptable way of terminating SWA when an electrical connection to the armour wires is required (i.e. most cases)
- Using BS 951 type earthing clamps (as used for bonding to water & gas pipes) to connect to the armour is a big no-no
- Taking SWA into an enclosure without the use of any form of gland is also unacceptable since the weight and rigidity of the cable means it must have mechanical support and fixing at entry to an enclosure.
This is a picture of the seven parts of the somewhat inappropriately named three part gland kit. This is the exterior waterproof style of gland. The interior version lacks the extra gland nut with the rubber insert that is used to seal the the gland against the cable. Beware that the "olive" might not be symmetrical along its rotation axis - look carefully at it when you disassemble your gland.
Step 1 - Assemble the gland parts on the wire
First cut the nose of the plastic boot, such that the hole left will be a snug fit over the outer sheath of the cable. Use the cable as guide to the size required. If you cut too little off the conical section you can cut more later, but if you cut too much then apart from throwing the conical rubber boot away and starting again then you may curse your own over-zealousness! :-) The further up the conical section of the boot you cut, the bigger the hole left :
Now slide the boot onto the cable, followed by the back nut with the rubber seal (external glands only), next the main armour fixing nut, and finally the fixing ring:
Step 2 - Stripping the outer insulation and cutting the amour
There are a couple of options here, which works best for you will depend a bit on the size of the cable and the tools you have to hand.
You need to leave enough length of free armour wires to fit over the cone section of the gland - about 30 - 40mm usually works for the smaller glands. Ideally you want the wires to splay at the same angle as the cone section to make assembly of the gland easier. Try to get the armour wires about the same length all round.
The "standard" approach is to work out where you will want the armour wires to end, and use a small hacksaw to cut a ring around the circumference of the cable, through the outer insulation, and about half way through the armour as you go. Once you have stripped the outer sheat, you should then be able to break off each of the wires with a quick wiggle.
Quick definition: Ringing: Rotating the cable against the knife blade, applying pressure with your thumb to the other side of the cable. Thus cutting through the outer insulation. When the armour is in place you can be quite firm here since the armour will protect the cable from any damage (but you will blunt your knife a little!):
Once the armour is gone, go back to a knife and slice down the outer as shown below to remove the outer insulation from your cut to the end of the cable:
Finally ring the outer insulation a little further up the cable to expose some of the armour ready for gland fitting. This method works well on the bigger cables.
A variation on this technique that works well for cables of up to about 10mm² is to cut the outer insulation and part cut the armour wires using a regular wheel type pipe cutter as would be used for copper pipe. Having used the pipe cutter to slice into the outmost layer of insulation, this cylinder could be removed from the cable. You may care to leave the insulation mostly in place by only pulling it (say) 50mm away (as in opening the cut by this amount or so). Then the pipe cutter can be used again to accurately mark the armoured wires for the next stage. The still-connected cylinder of plastic (which will soon be discarded) keeps the armour wires nice and tight to allow the pipe cutter to mark these wires without the wires having a free end to dislodge and rotate.
Alternatively, for the smaller ones you may find it as quick to start by ringing the outer sheath at the final sheath position, next slice down along the cable from the place you just cut round toward the free end, and finally pull off the outer sheath leaving the armour wires exposed at their full length:
Again the armour makes this easy with no risk of damaging the cable.
You can now trim the armour to length. Mark the cut position with a soft pencil, and then use a strong pair of side cutters to snip off the wires a few at a time:
This only works on the smaller cables since the armour wires on the larger ones get difficult to cut like this. However it is quite quick compared to a hacksaw.
Whichever method you use, when you are done you should now have something looking like this:
Step 3 - Stripping the bedding or inner insulation
Here we have to take care not to cut too deep or we will damage the individual conductor insulation. A deep score is usually enough. Next you can bend the inner at the scored point to break it. You should see a small gap open through which you can see the individual insulated wires:
(in practice it is probably better to leave a little more bedding on than shown in these photographs, so that it protrudes a little from the gland once fitted. This will offer a little more abrasion protection to the insulation on the conductors)
Step 4 - fitting the gland cone section
Once the wires are splayed out, you can slide the cone section onto the end of the wire. Take care to ensure that none of the armour wires slip inside the cone, or they will damage the inner bedding insulation when you tighten up the gland nuts:
Next slide up the armour gripping ring:
And finally screw the armour locking back nut onto the cone section. This will force the grip ring up the cone section of the gland and trap the armour wires firmly in the gland. Use a pair of spanners to tighten the gland parts:
Step 5 - sealing the back of the gland
Step 6 - Connecting to your box
Now the gland is fitted to the cable we can attach it to the actual box or panel that the cable is intended to connect to. For the smaller SWAs a 20mm knock out makes an ideal termination hole. Metal boxes often have pre-made holes ready to take SWA and conduit glands. Plastic ones will often need a knockout trimming out with a sharp knife first.
For this example we will terminate the gland on a standard metal box (this is a poor example in reality since you would be very unlikely to ever terminate at a flush mounting box like this since the gland assembly will need to remain accessible for maintenance (being a screwed electrical connection) - but it was what was to hand when the camera was poised! A more typical metal box would be one of the surface mounting metal clad types):
To make an effective earth connection to the armour there are a several ways of doing it. The standard way to do it is using the supplied earth tag (aka "banjo tag") and lock nut. If you need to keep the whole connection within the box then you may need to start by bending the tag a bit:
This will make fixing the earth wire to the tag simpler. Usually bolting your wire (via a suitable crimped terminal) is the easiest way to fix to the tag in the field. You can also solder to it but this is not always easy since there is a fair bit of metalwork to heat. If you do solder to the tag it is better to do it before it is mounted on the gland and in the box. On plastic boxes this will save you melting the plastic, and on metal ones it stops the extra metal conducting all the heat away and making it hard to solder.
The tag is now clamped between the box wall and the lock nut:
To bolt your wire to the tag it is best to crimp a ring terminal to the end of your wire:
In this circumstance it is often better to leave the tag flat, and drill a matching hole in the enclosure that lines up with the terminal hole on the tag. That way you can now bolt right through the tag and the enclosure. If you use a pan headed bolt, with the head on the outside of the box it does not look too untidy either. Note doing this is not recommended for boxes that need to remain completely waterproof.
A nicer solution however is to dispense with the tag and lock nut altogether, and use one of the proprietary fixing nuts like this that act as both lock nut, and also allow eye terminals to be screwed or bolted directly onto the nut.
With metal enclosures and boxes it is also acceptable to do away with the tag altogether and just rely on the interface between the gland and the box. If you are doing this it is vital that the mating surfaces of the box are cleaned to ensure no corrosion or paint will interfere with the connection, and also that the back nut is done up tightly. Note also that when the enclosure you are connecting to is to house an accessory (e.g. a socket) to comply with BS7671 [543-02-07], The earthing terminal of the enclosure must also be connected by a separate wire to the earth terminal on the accessory. Particular care is needed if the mounting plate that the gland fixes to is removable, since one may not rely on the screws that hold it as being a good enough earth connection on their own.
The final job is to slide the plastic boot into place, making a nice neat job:
Job Done! You can now get on and do the wiring... and the other end of the cable!
- Wiki Contents
- Wiki Subject Categories
- Taking electricity outside
- Wiring colour codes
- Cable Resistances