Difference between revisions of "Adding sockets"

From DIYWiki
(Cable Choice: m)
(asstd tidying up)
Line 1: Line 1:
{{Under-construction}} <!-- this includes the 'Under Construction' template -->
 
 
(this is a draft outline - feel free to add topics you would like to see covered)
 
 
 
This article covers the ways in which you can safely extend existing [[House Wiring for Beginners|socket circuits]] to provide more outlets.
 
This article covers the ways in which you can safely extend existing [[House Wiring for Beginners|socket circuits]] to provide more outlets.
  
Line 52: Line 48:
  
 
==Circuit joins==
 
==Circuit joins==
[[Cable]] joins in a circuit can be of 2 types:
+
See main article [[Electrical connection]]
 +
 
 +
[[Cable]] connections in a socket circuit can be of 2 types:
 
* accessible, meaning it can be reached readily using a [[Hand tool|tool]]
 
* accessible, meaning it can be reached readily using a [[Hand tool|tool]]
 
* inaccessible, eg buried under [[:Category:Tiling|tiling]]
 
* inaccessible, eg buried under [[:Category:Tiling|tiling]]
Line 68: Line 66:
  
 
===Junction boxes===
 
===Junction boxes===
 +
See main article [[Electrical connection]]
 +
 
===Disused cables===
 
===Disused cables===
 +
Ensure disused cables are disconnected at both ends.
  
 
==See also==
 
==See also==

Revision as of 07:12, 14 April 2011

This article covers the ways in which you can safely extend existing socket circuits to provide more outlets.

How many sockets

The choice is entirely yours. Just bear in mind that numerous socket additions have been made, only to find later that more are wanted. The amount of domestic electronics in use is continuing to increase, so what's adequate today probably won't be later.

Ring & Radial Circuits

British socket circuits are always ring or radial. A ring circuit makes a complete loop from CU (fusebox) to each socket and back to the CU. A radial only has a single run of cable from CU to the sockets, no return cable.

Extending radial circuits

Radials can be extended from any point in the radial circuit. See cable size section.

Extending ring circuits

New sockets can be added as part of the ring, or on a spur. Its very much recommended to add them as part of the ring where this is practical. This means breaking the existing ring, and often adding a bit more cable.

A relatively easy way to add new sockets as part of a ring is to cut the existing cable run and fit 2 new sockets, one to each end of the cable, then link the 2 with a new piece of cable. Extensions can also be included in a ring from a single existing socket position. See this technique.

Spurs

Sometimes running a single piece of cable from an existing point in the ciruit to a new socket is the only practical option. This is called a non-fused spur.

A non-fused spur should feed only one single or one twin socket-outlet, or one Fused Connection Unit. Three- and four-socket 'power strips' should be connected by a Fused Connection Unit or incorporate a 13A cartridge fuse.

The total number of non-fused spurs must not exceed the total number of socket outlets and items of stationary equipment that are directly connected to the circuit.

Splitting a ring

Occasionally it can be worthwhile to split a ring circuit. By breaking the circuit at some point, the one circuit then becomes 2x radial circuits. At the fusebox the 2 tails are separated, each getting its own fuse. Splitting the circuit like this changes the fuse rating permissible for each half, in most cases this makes it not worthwhile, but where a ring was run in 4 mm^2 you can get much more total ampacity by splitting it into 2 radials. One 30A or 32A 4mm ring can become 2x 32A radials.

When splitting a ring, regs require checking the voltage drops at the end of the new radials. Also check the current carrying capacities of the cables if they are buried in insulation, as the insulation leaves them able to handle less current.

Cable Choice

2.5 mm^2 is the most popular socket circuit cable. Its sufficiently rated for 30/32A ring circuits as long as its not buried in 100mm or more of insulation. Its also good for 20A fused radials as long as its not buried in 100mm or more of insulation.

4 mm^2 is used for 30/32A radial circuits, and 30/32A ring circuits where the cable will be buried in insulation. Trying to get 3x 4 mm^2 wires into socket terminals can be a challenge!

  • BS 3036 rewireable fuses aren't permitted on 30A 4mm radials due to the correction factor applied to the cable when using these type of fuses.

1.5 mm^2 cable is sometimes used on radial circuits where the circuit is fused at 15A and the cable won't be buried in 100mm or more of insulation. Where the cable is buried, 1.5 mm^2 can only be fused up to 10A. 1.5 mm^2 is typically used where an old immersion heater feed is reused to supply sockets.

Its ok to use larger cable than required if its able to fit into the terminals of the accessories in use.

Socket Positions

Cable Routes

Safe zones for electric cables

Cable routes and protection

RCD Protection

New sockets circuits normally require an RCD, though there are exceptions. Adding sockets to existing sockets does not require fitting an RCD. The RCD goes in the CU or fusebox - but some old fuseboxes can't accommodate an RCD.

Circuit joins

See main article Electrical connection

Cable connections in a socket circuit can be of 2 types:

  • accessible, meaning it can be reached readily using a tool
  • inaccessible, eg buried under tiling

Accessible joints are usually made using screw connections, either in the socket itself, or a junction box, or screwblock strip contained within an electrical backbox (for fire protection.)

Inaccessible joints may not use screw connections, as they can come loose in time. Permitted connection methods are:

Of these, crimping is by far the simplest and the least prone to problems in inexperienced hands.

The other approach to cable joins is to replace it with a new piece of cable that's long enough. Sometimes this is practical.

Junction boxes

See main article Electrical connection

Disused cables

Ensure disused cables are disconnected at both ends.

See also