Difference between revisions of "Pipe repair"
(Created page with "'''How to repair a leaking pipe''' - a beginner's guide right|250px right|250px The homeowner decided to insta...") |
(m pics) |
||
Line 2: | Line 2: | ||
− | [[image:IMAG2567-3 pipe oops.jpg|right| | + | [[image:IMAG2567-3 pipe oops.jpg|right|300px]] |
− | [[image:IMAG2574-3 oops.jpg|right| | + | [[image:IMAG2574-3 oops.jpg|right|300px]] |
The homeowner decided to install a fountain by wacking a [[nail]] through a [[floor]]board and into a [[pipe]]. | The homeowner decided to install a fountain by wacking a [[nail]] through a [[floor]]board and into a [[pipe]]. | ||
− | [[image:IMAG2572-3 Supplies.jpg|right| | + | [[image:IMAG2572-3 Supplies.jpg|right|300px]] |
Parts & [[tools]] - a couple of fairly big [[screwdriver]]s were also used as levers to move the [[pipe]] a tiny bit so the [[nut]] could turn. | Parts & [[tools]] - a couple of fairly big [[screwdriver]]s were also used as levers to move the [[pipe]] a tiny bit so the [[nut]] could turn. | ||
Line 13: | Line 13: | ||
You should be able to do it without spare olives, but I've had enough incidences of needing a new olive to always take spares. | You should be able to do it without spare olives, but I've had enough incidences of needing a new olive to always take spares. | ||
− | [[image:IMAG2573-3 Mark pipe.jpg|right| | + | [[image:IMAG2573-3 Mark pipe.jpg|right|300px]] |
Mark where to cut the [[pipe]]. Usually a rotating wheel type pipe cutter woud be used, but here there was no space for one. An oscillating [[saw]] was used - a hack[[saw]] is also possible. | Mark where to cut the [[pipe]]. Usually a rotating wheel type pipe cutter woud be used, but here there was no space for one. An oscillating [[saw]] was used - a hack[[saw]] is also possible. | ||
Line 19: | Line 19: | ||
Olives won't fit onto a sawn [[pipe]] end, so the pipe ends were filed to remove any external burr. This required getting the file in at a few odd angles. | Olives won't fit onto a sawn [[pipe]] end, so the pipe ends were filed to remove any external burr. This required getting the file in at a few odd angles. | ||
− | [[image:IMAG2575-3.jpg|right| | + | [[image:IMAG2575-3.jpg|right|300px]] |
Slide [[nut]] then olive on | Slide [[nut]] then olive on | ||
− | [[image:IMAG2576-3.jpg|right| | + | [[image:IMAG2576-3.jpg|right|300px]] |
Add linseed [[putty]]. | Add linseed [[putty]]. | ||
Line 29: | Line 29: | ||
Some people think you should never use gloop with [[compression fitting]]s because they were designed to be used dry. Choice is yours, fwiw I find they're more reliable on used pipes with putty. | Some people think you should never use gloop with [[compression fitting]]s because they were designed to be used dry. Choice is yours, fwiw I find they're more reliable on used pipes with putty. | ||
− | [[image:IMAG2578-3 tighten nut.jpg|right| | + | [[image:IMAG2578-3 tighten nut.jpg|right|300px]] |
Tighten each [[nut]]; the 2nd [[wrench]] stops the new plumbing rotating. I removed a 2nd [[floor]]board to get enough [[tool]] access. | Tighten each [[nut]]; the 2nd [[wrench]] stops the new plumbing rotating. I removed a 2nd [[floor]]board to get enough [[tool]] access. | ||
− | [[image:IMAG2581-3 pipe repaired.jpg|right| | + | [[image:IMAG2581-3 pipe repaired.jpg|right|300px]] |
Job done! | Job done! |
Revision as of 00:54, 29 November 2014
How to repair a leaking pipe - a beginner's guide
The homeowner decided to install a fountain by wacking a nail through a floorboard and into a pipe.
Parts & tools - a couple of fairly big screwdrivers were also used as levers to move the pipe a tiny bit so the nut could turn.
You should be able to do it without spare olives, but I've had enough incidences of needing a new olive to always take spares.
Mark where to cut the pipe. Usually a rotating wheel type pipe cutter woud be used, but here there was no space for one. An oscillating saw was used - a hacksaw is also possible.
Olives won't fit onto a sawn pipe end, so the pipe ends were filed to remove any external burr. This required getting the file in at a few odd angles.
Slide nut then olive on
Add linseed putty.
Some people think you should never use gloop with compression fittings because they were designed to be used dry. Choice is yours, fwiw I find they're more reliable on used pipes with putty.
Tighten each nut; the 2nd wrench stops the new plumbing rotating. I removed a 2nd floorboard to get enough tool access.
Job done!
This was a heating system pipe. So refill & repressurise heating according to boiler instructions. Add corrosion inhibitor ditto.
Nail floorboard back down, then you can repeat the whole process.