Difference between revisions of "Die grinder"
(→Cutting discs: aka) |
(more) |
||
Line 12: | Line 12: | ||
* 1/8" (3.17mm) bits fit right in | * 1/8" (3.17mm) bits fit right in | ||
* Other bit sizes must have 1/8" shank | * Other bit sizes must have 1/8" shank | ||
− | * Its possible to bulk smaller bits upto the right diameter by winding the bit with wire. Don't assume a collet will always hold such arrangements though | + | * Its possible to bulk smaller bits upto the right diameter by winding the bit with wire, but the wire diameter must be correct and diffrent for each bit size. Don't assume a collet will always hold such arrangements though |
− | * Its | + | * Its possible upto a point to grind 1/8" bits down to get smaller hole sizes, |
− | * | + | * Other size collets are also available |
* Thin [[Drill Bits|drill bits]] are very weak, sideways force or movement should be carefully avoided | * Thin [[Drill Bits|drill bits]] are very weak, sideways force or movement should be carefully avoided | ||
* Don't be tempted to try [[Drill Bits#PCB Drills|solid carbide bits]] in die grinders, in small sizes they are unsuitable and unsafe for [[:Category:Tools|handheld tools.]] | * Don't be tempted to try [[Drill Bits#PCB Drills|solid carbide bits]] in die grinders, in small sizes they are unsuitable and unsafe for [[:Category:Tools|handheld tools.]] | ||
Line 34: | Line 34: | ||
* Drilling occurs by both abrasion & melting | * Drilling occurs by both abrasion & melting | ||
* Speed of cut is good once the stone warms up. | * Speed of cut is good once the stone warms up. | ||
− | * No risk of cracking | + | * No risk of cracking the plastic |
* 1/4" holes drill easily & quickly | * 1/4" holes drill easily & quickly | ||
* Withdraw the tool without delay once it penetrates | * Withdraw the tool without delay once it penetrates | ||
Line 54: | Line 54: | ||
* Assorted shapes | * Assorted shapes | ||
− | ===Metal wire | + | ===Metal wire wheels=== |
[[image:Wire_wheel_0966-5.jpg|right|250px]] | [[image:Wire_wheel_0966-5.jpg|right|250px]] | ||
+ | [[image:Wire_cup_brushes_0977-4.jpg|right|250px]] | ||
* For removing rust, corrosion, [[Limescale|scale]] & [[Paint|paint]] | * For removing rust, corrosion, [[Limescale|scale]] & [[Paint|paint]] | ||
* very effective | * very effective | ||
− | * | + | * Full size angle grinder wire wheels are much quicker for most work |
* Can cause rust staining if used on concrete | * Can cause rust staining if used on concrete | ||
* Can also raise 3d grain in [[:Category:Wood|wood]] eg for moulds. | * Can also raise 3d grain in [[:Category:Wood|wood]] eg for moulds. | ||
− | + | * Brass wire wheels remove rust, paint etc without damaging steel workpieces | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | * | ||
− | |||
− | |||
===Nylon brush wheel=== | ===Nylon brush wheel=== | ||
[[image:Nylon_wheel_0979-4.jpg|right|250px]] | [[image:Nylon_wheel_0979-4.jpg|right|250px]] | ||
+ | [[image:Nylon_cup_brushes_0978-4.jpg|right|250px]] | ||
* [[:Category:Cleaning|Cleaning]] | * [[:Category:Cleaning|Cleaning]] | ||
* Removal of soft [[:Category:Materials|materials]] | * Removal of soft [[:Category:Materials|materials]] | ||
* Removal of loose [[Paint|paint]] | * Removal of loose [[Paint|paint]] | ||
− | * Plastic bristles mean it won't damage a much wider range of workpiece materials compared to | + | * Plastic bristles mean it won't damage a much wider range of workpiece materials compared to wire wheels |
** [[Scraper|detailed info]] | ** [[Scraper|detailed info]] | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
Line 110: | Line 87: | ||
− | === | + | ===Cutoff discs=== |
[[image:Cutting_discs_3199-3.jpg|right|250px]] | [[image:Cutting_discs_3199-3.jpg|right|250px]] | ||
− | |||
* The discs are very weak and break very readily. Expect to use a few even for a small job | * The discs are very weak and break very readily. Expect to use a few even for a small job | ||
* Take care to hold the grinder very steady, or disc will break impracticably quickly | * Take care to hold the grinder very steady, or disc will break impracticably quickly | ||
* [[Safety Goggles|Protective eyewear]] are best with these usually non-reinforced discs. | * [[Safety Goggles|Protective eyewear]] are best with these usually non-reinforced discs. | ||
− | * Reinforced cutting discs | + | * Reinforced cutting discs are tougher, but still not strong |
* Slow cutting compared to an [[angle grinder]] | * Slow cutting compared to an [[angle grinder]] | ||
* The very narrow kerf of a fraction of a mm is occasionally useful | * The very narrow kerf of a fraction of a mm is occasionally useful | ||
* Half worn discs can be used for access into very tight places | * Half worn discs can be used for access into very tight places | ||
+ | |||
===Sanding drum=== | ===Sanding drum=== | ||
[[image:Drum_sander_0968-4.jpg|right|250px]] | [[image:Drum_sander_0968-4.jpg|right|250px]] | ||
* Usually alox grit belts | * Usually alox grit belts | ||
− | * Loosen the end screw to release the belt | + | * Loosen the end [[screw]] to release the belt |
Line 136: | Line 113: | ||
===Sanding discs=== | ===Sanding discs=== | ||
[[image:Sanding_discs_0975-4.jpg|right|250px]] | [[image:Sanding_discs_0975-4.jpg|right|250px]] | ||
− | * Sandpaper discs are used with a | + | * Sandpaper discs are used with a backing pad |
* Typically weak and fine grained, making progress slow | * Typically weak and fine grained, making progress slow | ||
* Not really suitable for stock removal sanding | * Not really suitable for stock removal sanding | ||
Line 142: | Line 119: | ||
===Flap wheel=== | ===Flap wheel=== | ||
+ | [[image:Flap wheel 5757-2.jpg|right|250px]] | ||
* Sanding flaps | * Sanding flaps | ||
* For sanding non-flat surfaces | * For sanding non-flat surfaces | ||
+ | |||
+ | |||
+ | ===Cotton wheel=== | ||
+ | [[image:Cotton wheel 5755-2.jpg|right|250px]] | ||
+ | * Polishing | ||
+ | * Used with abrasive paste | ||
+ | |||
+ | |||
+ | ===Diamond cutoff disc=== | ||
+ | [[image:Diamond disc 5756-2.jpg|right|250px]] | ||
+ | * Not fragile | ||
+ | |||
+ | |||
+ | ===Collets=== | ||
+ | [[image:Collets 5758-2.jpg|right|250px]] | ||
+ | * Enables use of other drill bit sizes | ||
+ | * The set on the right covers 1/16" to 1/8" | ||
+ | |||
+ | |||
+ | ===Rubber polishing disc=== | ||
+ | [[image:Rubber abrasive polish disc 5759-2.jpg|right|250px]] | ||
+ | |||
==Tool Maintenance== | ==Tool Maintenance== | ||
Grinding stones can clog with [[:Category:Metal|metal]]. This can be removed either by a wirebrush, a coarse abrasive or a spiked wheel. | Grinding stones can clog with [[:Category:Metal|metal]]. This can be removed either by a wirebrush, a coarse abrasive or a spiked wheel. | ||
− | When grinding [[:Category:Metal|soft metals]] such as aluminium and copper, clogging can be a real problem. Rubbing the disc or stone firmly with chalk first | + | When grinding [[:Category:Metal|soft metals]] such as aluminium and copper, clogging can be a real problem. Rubbing the disc or stone firmly with chalk first can reduce clogging. |
Line 154: | Line 154: | ||
Linear speed of a 1" 30,000 rpm tool is around 2/3 of that of a 4.5" 11,000 rpm angle grinder tool. Also [[Angle Grinder Discs|angle grinder discs]] & brushes are much more robust. So more speed and force are available from an angle grinder than a die grinder. | Linear speed of a 1" 30,000 rpm tool is around 2/3 of that of a 4.5" 11,000 rpm angle grinder tool. Also [[Angle Grinder Discs|angle grinder discs]] & brushes are much more robust. So more speed and force are available from an angle grinder than a die grinder. | ||
− | The | + | The advantage of die grinders lies in their tiny size, which enables access in restricted spaces, and makes fine work with miniature [[:Category:Tools|tools]] practical. |
− | They are also generally much quieter than angle grinders, | + | They are also generally much quieter than angle grinders, occaionally an advantage. |
Finally more types of [[:Category:Tools|tool]] are available for die grinders than angle grinders. | Finally more types of [[:Category:Tools|tool]] are available for die grinders than angle grinders. | ||
Line 168: | Line 168: | ||
# They de-rust old tools well | # They de-rust old tools well | ||
# I use mine with a small grinding bit to trim my toenails. The tiny little grinders the cosmetic firms sell for this purpose are utterly useless, but the Dremel is first rate! | # I use mine with a small grinding bit to trim my toenails. The tiny little grinders the cosmetic firms sell for this purpose are utterly useless, but the Dremel is first rate! | ||
+ | |||
==Speed== | ==Speed== | ||
Line 187: | Line 188: | ||
==Safety== | ==Safety== | ||
− | The main risk with these machines is explosion of the tool due to breakage at very high | + | The main risk with these machines is explosion of the cutting/grinding tool due to breakage at very high speed. Running over rated speed can cause tools to shatter explosively. |
− | |||
− | |||
− | Cutting discs | + | Cutting discs break extremely easily. |
Wire brushes are prone to shedding bristles. These shed bristles come off at high speed, often sharp point first. Some wire brushes have a reduced speed rating. | Wire brushes are prone to shedding bristles. These shed bristles come off at high speed, often sharp point first. Some wire brushes have a reduced speed rating. | ||
− | Eye protection | + | Eye protection shold be used, and one should stay out of the plane of spin of the tool. |
− | A second risk results from high speed, tool inertia and absence of guarding. Catching a spinning tool on something can yank the machine | + | A second risk results from high speed, tool inertia and absence of guarding. Catching a spinning tool on something can yank the machine. The machine should be held firmly, hands kept out of the way of the tool, and force on the workpiece should always be kept light. |
− | Tools that cause vibration should be retired. These | + | Tools that cause vibration should be retired. These are much more liable to fail dangerously in use. They also put high stresses on machine bearings causing premature failure. |
Revision as of 21:57, 11 May 2012
A Die Grinder is a small high speed rotary power tool. Typically these take an array of tools of upto 1.5" diameter with 1/8" (3.17mm) shank.
Dremel is a popular make of die grinder, and the word Dremel is widely used to mean a die grinder (of any brand).
Tools
Many types of tools are used with these machines.
Drill bit
- 1/8" (3.17mm) bits fit right in
- Other bit sizes must have 1/8" shank
- Its possible to bulk smaller bits upto the right diameter by winding the bit with wire, but the wire diameter must be correct and diffrent for each bit size. Don't assume a collet will always hold such arrangements though
- Its possible upto a point to grind 1/8" bits down to get smaller hole sizes,
- Other size collets are also available
- Thin drill bits are very weak, sideways force or movement should be carefully avoided
- Don't be tempted to try solid carbide bits in die grinders, in small sizes they are unsuitable and unsafe for handheld tools.
- Larger holes can be drilled in plastic using a different method
Grind stones
- Various shapes, & a few compounds & grades.
- Aluminium oxide is used for most grinding stones, and isn't very good at grinding steel.
- Alox stones come in various light colours.
- Carbide stones are good for steel. These are dark grey, and several times the price of alox.
- Use depends on the material and shape of the bit
Drilling with grind stone
Plastics can be drilled with a pointed cylindrical alox grind stone.
- Drilling occurs by both abrasion & melting
- Speed of cut is good once the stone warms up.
- No risk of cracking the plastic
- 1/4" holes drill easily & quickly
- Withdraw the tool without delay once it penetrates
- Makes a mess of the stone
Spiral saw
- 1/8" spiral saw bits can be used in die grinders
- Sideways cutting with a thin weak bit isn't the best combination
- Their uses are limited
Diamond coated engraving bits
- For engraving glass
- Also security marks hard surfaces
- Postcode and often house number are the usual info engraved
- Assorted shapes
Metal wire wheels
- For removing rust, corrosion, scale & paint
- very effective
- Full size angle grinder wire wheels are much quicker for most work
- Can cause rust staining if used on concrete
- Can also raise 3d grain in wood eg for moulds.
- Brass wire wheels remove rust, paint etc without damaging steel workpieces
Nylon brush wheel
- Cleaning
- Removal of soft materials
- Removal of loose paint
- Plastic bristles mean it won't damage a much wider range of workpiece materials compared to wire wheels
Felt polishing pads
- Polishing metal, plastics,
- Use with polishing compound
- Can also be used to create the circular swirl pattern finish sometimes seen on metalwork
Screw mandrel
- These hold felt polishing pads
- The screw thread tip just screws into the felt pad
Cutoff discs
- The discs are very weak and break very readily. Expect to use a few even for a small job
- Take care to hold the grinder very steady, or disc will break impracticably quickly
- Protective eyewear are best with these usually non-reinforced discs.
- Reinforced cutting discs are tougher, but still not strong
- Slow cutting compared to an angle grinder
- The very narrow kerf of a fraction of a mm is occasionally useful
- Half worn discs can be used for access into very tight places
Sanding drum
- Usually alox grit belts
- Loosen the end screw to release the belt
Rasps
- High speed coarse cutters
- Fast shaping of soft metals, plastics, wood etc
- Don't try to use on high strength materials such as steel or concrete
Sanding discs
- Sandpaper discs are used with a backing pad
- Typically weak and fine grained, making progress slow
- Not really suitable for stock removal sanding
Flap wheel
- Sanding flaps
- For sanding non-flat surfaces
Cotton wheel
- Polishing
- Used with abrasive paste
Diamond cutoff disc
- Not fragile
Collets
- Enables use of other drill bit sizes
- The set on the right covers 1/16" to 1/8"
Rubber polishing disc
Tool Maintenance
Grinding stones can clog with metal. This can be removed either by a wirebrush, a coarse abrasive or a spiked wheel.
When grinding soft metals such as aluminium and copper, clogging can be a real problem. Rubbing the disc or stone firmly with chalk first can reduce clogging.
Performance
Linear speed of a 1" 30,000 rpm tool is around 2/3 of that of a 4.5" 11,000 rpm angle grinder tool. Also angle grinder discs & brushes are much more robust. So more speed and force are available from an angle grinder than a die grinder.
The advantage of die grinders lies in their tiny size, which enables access in restricted spaces, and makes fine work with miniature tools practical.
They are also generally much quieter than angle grinders, occaionally an advantage.
Finally more types of tool are available for die grinders than angle grinders.
Usefulness
How useful are they is a question often asked. Personal experiences follow.
- I rarely use mine, but when I do, nothing else will do.
- I last used one for cutting out some bearings. I don't know any other tool that could have done the job.
- They can be used for cutting pipes in awkward places.
- They de-rust old tools well
- I use mine with a small grinding bit to trim my toenails. The tiny little grinders the cosmetic firms sell for this purpose are utterly useless, but the Dremel is first rate!
Speed
These tools operate at extremely high rotational speed, and one should check that the tools used are rated for the speed of the machine. There are tools available rated at below typical machine speeds, and these should not be used above their rated speed on safety grounds.
Reducing speed
Some machines can be set to reduced speed to enable lower speed tools to be used, some can't. For machines with no speed control there are some workarounds for speed reduction.
- Running the tool off a 110v transformer gives a max speed of 110/240 x the usual run speed
- When no better alternative is to hand, running a lightbulb in series with the die grinder reduces the voltage and thus speed.
- A multimeter is used to measure the offload voltage and thus calculate max speed. The downside of this arrangement is that as the tool is loaded its speed will reduce at a greater than usual rate as load increases.
- Low voltage tools can be run off a supply of lower voltage to reduce speed.
Speed = voltage/rated voltage x rated speed.
This holds true for both mains and low voltage machines.
See Droppers for more information
Safety
The main risk with these machines is explosion of the cutting/grinding tool due to breakage at very high speed. Running over rated speed can cause tools to shatter explosively.
Cutting discs break extremely easily.
Wire brushes are prone to shedding bristles. These shed bristles come off at high speed, often sharp point first. Some wire brushes have a reduced speed rating.
Eye protection shold be used, and one should stay out of the plane of spin of the tool.
A second risk results from high speed, tool inertia and absence of guarding. Catching a spinning tool on something can yank the machine. The machine should be held firmly, hands kept out of the way of the tool, and force on the workpiece should always be kept light.
Tools that cause vibration should be retired. These are much more liable to fail dangerously in use. They also put high stresses on machine bearings causing premature failure.