Difference between revisions of "DIY Heat Bank"
(→Flow Switch: Redrew snubber circuit) |
(→Introduction: re-scale picture to look less ugly) |
||
(6 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
+ | ==Introduction== | ||
This article is about making a [[DHW]] [[Thermal Stores and Heat Banks|Heat Bank]] using readily-available separate components. | This article is about making a [[DHW]] [[Thermal Stores and Heat Banks|Heat Bank]] using readily-available separate components. | ||
− | + | [[Image:Heat-Bank-Water.gif|768px|Click for larger image]] | |
− | + | ||
− | + | '''Example Construction''' | |
− | + | [[Image:DIY_Heat_Bank_DHW_secondary_components.jpg|thumb|left|Caption click for larger picture]] | |
+ | |||
+ | |||
+ | |||
DHW secondary components assembled ready to install (remotely from cylinder). A service isolation valve and in-line 'Y' strainer are visible in the mains water inlet (bottom right) which are not shown in the diagram. The electrical connections to the pump and flow switch, and the triac electronics are not shown in this photograph. | DHW secondary components assembled ready to install (remotely from cylinder). A service isolation valve and in-line 'Y' strainer are visible in the mains water inlet (bottom right) which are not shown in the diagram. The electrical connections to the pump and flow switch, and the triac electronics are not shown in this photograph. | ||
− | |||
== Components == | == Components == | ||
− | Normal [[Central_Heating_Controls_and_Zoning# CH and DHW zones: Y-plan|Y-plan]] (or S-plan, W-plan etc) [[Central_Heating_Design# Filling arrangements: sealed or vented|vented]] [[Central | + | Normal [[Central_Heating_Controls_and_Zoning# CH and DHW zones: Y-plan|Y-plan]] (or S-plan, W-plan etc) [[Central_Heating_Design# Filling arrangements: sealed or vented|vented]] [[Central heating|CH+DHW system]] with |
* '''Direct HW cylinder''' (a standard Indirect cylinder could be used, either with extra tappings via e.g. Essex flanges, or Tee-ing the connections from the boiler into the top and (existing) bottom connections of the cylinder.) | * '''Direct HW cylinder''' (a standard Indirect cylinder could be used, either with extra tappings via e.g. Essex flanges, or Tee-ing the connections from the boiler into the top and (existing) bottom connections of the cylinder.) | ||
* '''Pump''' (standard 15/50 CH circulator type) | * '''Pump''' (standard 15/50 CH circulator type) | ||
Line 132: | Line 135: | ||
[[Image:FlowSwitchSnubber.gif]] | [[Image:FlowSwitchSnubber.gif]] | ||
+ | |||
+ | |||
+ | '''Suitable Components:''' | ||
+ | |||
+ | {| border="1" cellpadding="6" cellspacing="0" style="text-align:left" | ||
+ | !Part | ||
+ | !Suitable Component | ||
+ | !Suppliers order code (CPC) | ||
+ | |- | ||
+ | | Flow Switch || Also available from CPC || [http://cpc.farnell.com/crydom/fs22/liquid-flow-switch-3-5-15va/dp/SN35601?Ntt=FS22FLOWSWITCH SN35601] | ||
+ | |- | ||
+ | | Triac || STMicro BTA16-600B || [http://cpc.farnell.com/stmicroelectronics/bta16-600b/triac-16a-600v-to-220ab/dp/SC07585?Ntt=SC07585 SC07585] | ||
+ | |- | ||
+ | |The Metal Oxide Varistor (MOV) || Epcos B722 Series || [http://cpc.farnell.com/epcos/b72205s251k101/varistor-8-2j-250vac/dp/RE03667?Ntt=RE03667 RE03667] | ||
+ | |- | ||
+ | |Snubber network<br>contact suppressor<br>(shown on the motor)||can either be assembled from basic components, or a module such as the Ampohm FE-SP-HDR-23-100/100 could be used. || [http://cpc.farnell.com/ampohm-wound-products/fe-sp-hdr23-100-100/contact-suppressor-0-1uf-100r/dp/FT00715?Ntt=FT00715 FT00715] | ||
+ | |- | ||
+ | |} | ||
+ | |||
* [http://groups.google.co.uk/group/sci.electronics.design/browse_frm/thread/259e31826ee77ccf/e24a054b9101e889 Discussion of design of circuit] from sci.electronics.design | * [http://groups.google.co.uk/group/sci.electronics.design/browse_frm/thread/259e31826ee77ccf/e24a054b9101e889 Discussion of design of circuit] from sci.electronics.design | ||
Line 139: | Line 161: | ||
=== TMV === | === TMV === | ||
This is a standard 22mm Thermostatic Mixing valve used for limiting the temperature of water to washbasins in hospitals, schools etc to prevent scalding. Available from [http://www.screwfix.com/app/sfd/cat/pro.jsp?id=18732 Screwfix], [http://www.toolstation.com/index.html?code=29695 Toolstation] etc. | This is a standard 22mm Thermostatic Mixing valve used for limiting the temperature of water to washbasins in hospitals, schools etc to prevent scalding. Available from [http://www.screwfix.com/app/sfd/cat/pro.jsp?id=18732 Screwfix], [http://www.toolstation.com/index.html?code=29695 Toolstation] etc. | ||
− | |||
== See Also == | == See Also == | ||
Line 147: | Line 168: | ||
* [[Domestic Hot Water Systems]] | * [[Domestic Hot Water Systems]] | ||
* [[Thermal Stores and Heat Banks]] | * [[Thermal Stores and Heat Banks]] | ||
− | * [[Central | + | * [[Central heating]] |
[[Category:Heating]] | [[Category:Heating]] | ||
[[Category:Plumbing]] | [[Category:Plumbing]] | ||
[[Category: Domestic Hot Water]] | [[Category: Domestic Hot Water]] |
Latest revision as of 10:32, 21 November 2017
Introduction
This article is about making a DHW Heat Bank using readily-available separate components.
Example Construction
DHW secondary components assembled ready to install (remotely from cylinder). A service isolation valve and in-line 'Y' strainer are visible in the mains water inlet (bottom right) which are not shown in the diagram. The electrical connections to the pump and flow switch, and the triac electronics are not shown in this photograph.
Components
Normal Y-plan (or S-plan, W-plan etc) vented CH+DHW system with
- Direct HW cylinder (a standard Indirect cylinder could be used, either with extra tappings via e.g. Essex flanges, or Tee-ing the connections from the boiler into the top and (existing) bottom connections of the cylinder.)
- Pump (standard 15/50 CH circulator type)
- Plate Heat Exchanger (PHE)
- Thermostatic Mixing Valve (TMV) 22mm
- Flow switch wired to switch on pump when flow is detected
PHE
From:
GEA-Ecoflex Unit 8, Waterside Business Park Redwall Close Dinnington-Sheffield S25 3QA Tel.: +44-(0)1909 551 107 Fax: +44-(0)1909 550 885 e-mail: info.uk@gea-ecoflex.com
Copper brazed plate heat exchanger model:- BP12M-20-G1G1
Spec
Compact gasket-free Brazed Plate Heat Exchanger consisting of corrugated pressed stainles steel plates (1.4401), which are brazed together with copper in a special vacuum process. Designed, produced and tested in sites with quality systems in accordance with DIN ISO 9002 requirements. Pressure-Vessel Approval according TÜV and EC Pressure-Equipment-Directive (CE).
Specification for 1 x M12-20-GG | ||||
---|---|---|---|---|
Operational data: | Side A | Side B | ||
Media: | Water | Water | ||
Condition: | liquid | liquid | ||
Heat exchanged: | 50 | kW | ||
Mass flow: | ||||
Volume flow: | 0.64 | 0.24 | l/s | |
Temperature inlet: | 82 | 10 | °C | |
Temperature outlet: | 63 | 60 | °C | |
Pressure drop: | 29.65 | 3.91 | kPa | |
Surface margin: | 1.49 | % | ||
Content: | 0.5 | l | ||
Heat transfer area: | 0.22 | m² | ||
Design pressure: | 30 | bar | ||
Design temperature: | 200 | °C |
Note this is probably under-sized for this application: 100kW would be preferable.
Flow Switch
Farnell order code 730890 Manufacturer Part Number FS22 FLOW SWITCH, 22MM 3.75 L/MIN; Switch Poi £11.60 + VAT & p&p
This is a reed-switch whose contacts are rated 15VA, max 1A AC, into resistive loads.
The pump is rated 82W, 0.36A @ 230V AC and is an inductive load so the circuit shown is used to drive it.
Suitable Components:
Part | Suitable Component | Suppliers order code (CPC) |
---|---|---|
Flow Switch | Also available from CPC | SN35601 |
Triac | STMicro BTA16-600B | SC07585 |
The Metal Oxide Varistor (MOV) | Epcos B722 Series | RE03667 |
Snubber network contact suppressor (shown on the motor) |
can either be assembled from basic components, or a module such as the Ampohm FE-SP-HDR-23-100/100 could be used. | FT00715 |
- Discussion of design of circuit from sci.electronics.design
An alternative requiring no electronics would be to use a flow switch capable of switching the pump directly. These ara available from DPS.
TMV
This is a standard 22mm Thermostatic Mixing valve used for limiting the temperature of water to washbasins in hospitals, schools etc to prevent scalding. Available from Screwfix, Toolstation etc.
See Also
- Discussion: Home Made Heat Bank on uk.d-i-y
- Discussion: DIY Heatbank - fine tuning of system (incl CH) on uk.d-i-y
- Domestic Hot Water
- Domestic Hot Water Systems
- Thermal Stores and Heat Banks
- Central heating