Search results

• Power Tools
  *[http://www.diyfaq.org.uk/powertools/sander.htm Belt sander] *[http://www.diyfaq.org.uk/powertools/sander.htm Delta Sander]
  3 KB (504 words) - 11:32, 2 July 2012
• Tools Links
  * [http://www.diyfaq.org.uk/powertools/sander.htm Belt sander] * [http://www.diyfaq.org.uk/powertools/sander.htm Delta Sander]
  5 KB (858 words) - 20:34, 29 August 2017
• Oak Drawer Organiser
  ...o do any real sanding requires you getting quite medieval on it! So a belt sander with 40 grit is where I started, then 80 before finishing with 120 grit. ...the boards cut at once on the bandsaw before being cleaned up on a spindle sander.
  4 KB (693 words) - 04:21, 15 August 2015
• Sanders
  ...and, but a machine can make it very much faster in some cases&#33; </p><h2>Sander types</h2> ...r commonly found as fixed workshop tools (often in combination with a belt sander). These are often equipped with a "table" to support the work being sanded
  12 KB (2,195 words) - 01:23, 16 October 2019
• Planer knife sharpening jig
  ...surface covered with abrasive papers, of could also be done on a long belt sander or linisher if available. ...ess you need to polish out large knicks from the blades). If using a power sander, take care not to overheat the blades as this will soften the steel. After
  4 KB (695 words) - 23:41, 23 February 2014
• Dust collection
  ===Sander===
  8 KB (1,441 words) - 00:00, 11 December 2010
• Router inlay jig
  ...ail mounted on the underside that matches the slot in the table on my disc sander: ...radius. When close to the desired radius, you rotate the disc against the sander. This will make a close to perfect round. Finally take a light final pass t
  8 KB (1,444 words) - 14:32, 22 May 2020
• Appliance power consumption
  * Belt Sander 380W
  2 KB (341 words) - 19:53, 16 September 2018
• Bed Slats
  ...ds. This is easily achieved with a plane, or even a stock removing type of sander if a better tool is not available. CLS timber comes pre-rounded.
  3 KB (561 words) - 00:02, 23 July 2019
• Coffee table - Limbert style
  ...then cut on the [[bandsaw]], and finished to the final shape using a belt sander. ...and also to hide any errors in the board alignment using a hand held belt sander with a coarse 40 grit belt (dry oak really does take some effort to sand!)
  14 KB (2,478 words) - 15:24, 16 February 2023
• Electrics, Socket Chasing (Flush with wall)
  ...a [[knives|knife]] or the back of a knife. Then use an orbital (or other) sander (belt not recommended) to level the surfaces with the existing plaster.
  6 KB (1,122 words) - 16:44, 20 May 2009
• Oscillating tools
  An oscillating tool, looks a little reminiscent of a detail sander, and in fact they do make very good detail sanders. However that is where t ...nto it, or hammering against an edge as you would with a traditional delta sander.
  13 KB (2,110 words) - 23:58, 10 September 2018
• Recondition a Wood Floor
  ...urface paint is not nearly as drastic as the results of a large flat floor sander. However it does remove patina.
  12 KB (2,091 words) - 14:31, 4 December 2017
• RTL3 Speaker repair
  ...e case with wood dust, so instead I opted for a small electric narrow belt sander. This has the advantage of "pulling" all the dust out of the case toward th
  5 KB (768 words) - 15:58, 30 June 2022
• Knife sharpening
  ===Belt sander=== ...ry effective. If you've not come across this tool before it's like a belt sander but the belts are only 12mm (IIRC) wide. It allows me more control than my
  19 KB (3,210 words) - 19:37, 17 July 2014
• Dining chair - cushion replacement
  ...a sheet of 9mm MDF. I cut out the MDF with a jigsaw, and then used a belt sander to get a nice shape and finish all round it.
  6 KB (960 words) - 08:36, 11 September 2019
• Angle grinder
  * as a high speed metal sander ...stock removing sander, with linear speeds far in excess of other types of sander. This and the crescent shaped pressure area make them a poor choice for fin
  20 KB (3,302 words) - 19:26, 8 January 2022
• Library chair
  ...son Wax, and then buffed that up with a polishing bonnet on a random orbit sander. The result was a soft satin finish and a very nice to the hand smooth touc
  5 KB (854 words) - 15:32, 28 June 2016
• Desktop apothecary drawers and shelf
  ...rCornerCoarseSanded.jpg|thumb|300x300px|Once that was set, I used the disc sander to get that shaped close to size]] ...umb|Finally that could be sanded flush on all sides with the hand held ROS sander.]]
  19 KB (3,576 words) - 01:18, 7 September 2023
• Cabinet clock
  After the cut, the profile was sanded to the line using a drum sander in a drill press: ...e clamped a bit of MDF with a cutout onto the drill table just so that the sander can reach the bottom edge of the work when sat square on the table)
  20 KB (3,713 words) - 10:16, 15 October 2011

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)